Thermon TraceNet TCM 18 Uživatelský manuál stáhnout pdf (Strana 34)

Figure 17: Programming Keys

The display screen will now shift the cursor to the next value to program as shown

in the following display.

PROGRAM CIRCUIT = 7

MAINTAIN TEMPERATURE

MAINT= 49

◦

C← 49

◦

Figure 18: Changing Maintain Temperature

A single press of the green UP or DOWN arrow programming key will increase or

lower the Maintain Temperature set point by a single degree. Holding these keys

down will increase the indexing speed for cases where a signiﬁcantly large increase

or decrease in set point is required. Once the new set point is reached, press the

green ENTER key to save the new set point.

PN 50316_0514 30

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 95 96

TraceNet™ TC 1
Series Control System 1
Maintenance Guide 2
Contents 3
1 Introduction 5
PN 50316_0514 2 6
2 Speciﬁcations 7
5 PN 50316_0514 9
3 Module Connections 11
PN 50316_0514 8 12
The RTB6 Module Connections 13
The PM6 Connections 14
The RM6 Connections 15
4 Field and Panel Wiring 16
13 PN 50316_0514 17
Figure 6: RTD Sensor Location 17
TraceNet Panel Wiring 18
Serial Communication Wiring 18
PN 50316_0514 19
5 Monitoring Heat 20
17 PN 50316_0514 21
PN 50316_0514 18 22
19 PN 50316_0514 23
PN 50316_0514 20 24
21 PN 50316_0514 25
6 Accessing Heat Tracing 26
Figure 12: TCM18 LCD Response 27
23 PN 50316_0514 27
PN 50316_0514 24 28
25 PN 50316_0514 29
(1, 2, 3, 4, 5) 30
PN 50316_0514 26 30
7 Programming the 31
PROGRAM MODE ENABLED 32
SELECT FUNCTION KEY 32
Press the MAINTAIN TEMP key 32
Figure 15: MAINTAIN TEMP Key 33
29 PN 50316_0514 33
Figure 17: Programming Keys 34
Figure 19: The ENTER Key 35
31 PN 50316_0514 35
Figure 21: The PROG Key 36
33 PN 50316_0514 37
PN 50316_0514 34 38
35 PN 50316_0514 39
PN 50316_0514 36 40
37 PN 50316_0514 41
PN 50316_0514 38 42
39 PN 50316_0514 43
PN 50316_0514 40 44
41 PN 50316_0514 45
PN 50316_0514 42 46
43 PN 50316_0514 47
PN 50316_0514 44 48
45 PN 50316_0514 49
8 Heat Trace Control and 50
47 PN 50316_0514 51
9 The TCM18 in 52
Figure 24: Heater Setup 53
49 PN 50316_0514 53
Figure 25: Select RTD Setup 54
10 The TCM18 in 55
PN 50316_0514 52 56
11 The TCM18 Data 57
12 System Start-Up 58
13 Maintenance 59
PN 50316_0514 56 60
57 PN 50316_0514 61
Wiring and Connections Survey 62
59 PN 50316_0514 63
14 Notes 64
61 PN 50316_0514 65
15 More Information 66
Appendix A 67
Trouble Shooting Tips 67
PN 50316_0514 64 68
Low Temperature Reading/Alarm 69
PN 50316_0514 66 70
67 PN 50316_0514 71
RTD Sensor Alarm 72
Communications Alarm 72
Circuit Fault Alarm 73
High Current Readings/Alarms 73
PN 50316_0514 70 74
Low Current Readings/Alarms 75
PN 50316_0514 72 76
High Ground Current Alarm 77
PN 50316_0514 74 78
Appendix B Temperature and 79
Current Limits 79
PN 50316_0514 76 80
Appendix C 81
Advanced Features of the 81
TCM18 Ambient Control 81
PN 50316_0514 78 82
79 PN 50316_0514 83
Appendix D Typical TCM18 84
Control Applications 84
81 PN 50316_0514 85
83 PN 50316_0514 87
85 PN 50316_0514 89
PIPE TEMPERATURE 90
DEGREES CELSIUS 90
87 PN 50316_0514 91
89 PN 50316_0514 93
Appendix E Utilities 94
Appendix F Markings for 95
Explosive Atmospheres) 95
Thermon Manufacturing Company 96
100 Thermon Drive 96
San Marcos Texas 96
Thermon PN 50316_0514 96

Komentáře k této Příručce

Žádné komentáře

Thermon TraceNet TCM 18 Uživatelský manuál Strana 34

Komentáře k této Příručce

Související produkty a manuály pro Hardware Thermon TraceNet TCM 18